Frequency synthesizer

A frequency synthesizer is an electronic circuit that generates a range of frequencies from a single reference frequency. Frequency synthesizers are used in many modern devices such as radio receivers, televisions, mobile telephones, radiotelephones, walkie-talkies, CB radios, cable television converter boxes satellite receivers, and GPS systems. A frequency synthesizer may use the techniques of frequency multiplication, frequency division, direct digital synthesis, frequency mixing, and phase-locked loops to generate its frequencies. The stability and accuracy of the frequency synthesizer's output are related to the stability and accuracy of its reference frequency input. Consequently, synthesizers use stable and accurate reference frequencies, such as those provided by crystal oscillators.

Types

Three types of synthesizer can be distinguished. The first and second type are routinely found as stand-alone architecture: direct analog synthesis (also called a mix-filter-divide architecture as found in the 1960s HP 5100A) and the more modern direct digital synthesizer (DDS) (table-look-up). The third type are routinely used as communication system IC building-blocks: indirect digital (PLL) synthesizers including integer-N and fractional-N.

Digiphase synthesizer

It is in some ways similar to a DDS, but it has architectural differences. One of its big advantages is to allow a much finer resolution than other types of synthesizers with a given reference frequency.

History

Prior to widespread use of synthesizers, in order to pick up stations on different frequencies, radio and television receivers relied on manual tuning of a local oscillator, which used a resonant circuit composed of an inductor and capacitor, or sometimes resonant transmission lines; to determine the frequency. The receiver was adjusted to different frequencies by either a variable capacitor, or a switch which chose the proper tuned circuit for the desired channel, such as with the turret tuner commonly used in television receivers prior to the 1980s. However the resonant frequency of a tuned circuit is not very stable; variations in temperature and aging of components caused frequency drift, causing the receiver to drift off the station frequency. Automatic frequency control (AFC) solves some of the drift problem, but manual retuning was often necessary. Since transmitter frequencies are stabilized, an accurate source of fixed, stable frequencies in the receiver would solve the problem.

Quartz crystal resonators are many orders of magnitude more stable than LC circuits and when used to control the frequency of the local oscillator offer adequate stability to keep a receiver in tune. However the resonant frequency of a crystal is determined by its dimensions and cannot be varied to tune the receiver to different frequencies. One solution is to employ many crystals, one for each frequency desired, and switch the correct one into the circuit. This "brute force" technique is practical when only a handful of frequencies are required, but quickly becomes costly and impractical in many applications. For example, the FM radio band in many countries supports 100 individual channel frequencies from about 88 MHz to 108 MHz; the ability to tune in each channel would require 100 crystals. Cable television can support even more frequencies or channels over a much wider band. A large number of crystals increases cost and requires greater space.

The solution to this was the development of circuits which could generate multiple frequencies from a "reference frequency" produced by a crystal oscillator. This is called a frequency synthesizer. The new "synthesized" frequencies would have the frequency stability of the master crystal oscillator, since they were derived from it.

Many techniques have been devised over the years for synthesizing frequencies. Some approaches include phase locked loops, double mix, triple mix, harmonic, double mix divide, and direct digital synthesis (DDS). The choice of approach depends on several factors, such as cost, complexity, frequency step size, switching rate, phase noise, and spurious output.

Coherent techniques generate frequencies derived from a single, stable master oscillator. In most applications, a crystal oscillator is common, but other resonators and frequency sources can be used. Incoherent techniques derive frequencies from a set of several stable oscillators. The vast majority of synthesizers in commercial applications use coherent techniques due to simplicity and low cost.

Synthesizers used in commercial radio receivers are largely based on phase-locked loops or PLLs. Many types of frequency synthesizer are available as integrated circuits, reducing cost and size. High end receivers and electronic test equipment use more sophisticated techniques, often in combination.

System analysis and design

A well-thought-out design procedure is considered to be the first significant step to a successful synthesizer project. In the system design of a frequency synthesizer, states Manassewitsch, there are as many "best" design procedures as there are experienced synthesizer designers. System analysis of a frequency synthesizer involves output frequency range (or frequency bandwidth or tuning range), frequency increments (or resolution or frequency tuning), frequency stability (or phase stability, compare spurious outputs), phase noise performance (e.g., spectral purity), switching time (compare settling time and rise time), and size, power consumption, and cost. James A. Crawford says that these are mutually contradictive requirements.

Influential early books on frequency synthesis techniques include those by Floyd M. Gardner (his 1966 Phaselock techniques) and by Venceslav F. Kroupa (his 1973 Frequency Synthesis).

Mathematical techniques analogous to mechanical gear-ratio relationships can be employed in frequency synthesis when the frequency synthesis factor is a ratio of integers. This method allows for effective planning of distribution and suppression of spectral spurs.

Variable-frequency synthesizers, including DDS, are routinely designed using Modulo-N arithmetic to represent phase.

Principle of PLL synthesizers

See main article: Phase-locked loop

A phase locked loop is a feedback control system. It compares the phases of two input signals and produces an error signal that is proportional to the difference between their phases. The error signal is then low pass filtered and used to drive a voltage-controlled oscillator (VCO) which creates an output frequency. The output frequency is fed through a frequency divider back to the input of the system, producing a negative feedback loop. If the output frequency drifts, the phase error signal will increase, driving the frequency in the opposite direction so as to reduce the error. Thus the output is locked to the frequency at the other input. This other input is called the reference and is usually derived from a crystal oscillator, which is very stable in frequency. The block diagram below shows the basic elements and arrangement of a PLL based frequency synthesizer.

Block diagram of a common type of PLL synthesizer.

The key to the ability of a frequency synthesizer to generate multiple frequencies is the divider placed between the output and the feedback input. This is usually in the form of a digital counter, with the output signal acting as a clock signal. The counter is preset to some initial count value, and counts down at each cycle of the clock signal. When it reaches zero, the counter output changes state and the count value is reloaded. This circuit is straightforward to implement using flip-flops, and because it is digital in nature, is very easy to interface to other digital components or a microprocessor. This allows the frequency output by the synthesizer to be easily controlled by a digital system.

Example

Suppose the reference signal is 100 kHz, and the divider can be preset to any value between 1 and 100. The error signal produced by the comparator will only be zero when the output of the divider is also 100 kHz. For this to be the case, the VCO must run at a frequency which is 100 kHz x the divider count value. Thus it will produce an output of 100 kHz for a count of 1, 200 kHz for a count of 2, 1 MHz for a count of 10 and so on. Note that only whole multiples of the reference frequency can be obtained with the simplest integer N dividers. Fractional N dividers are readily available.

Practical considerations

Philips TDA6651TT - 5 V mixer/oscillator and low noise PLL synthesizer for hybrid terrestrial tuner

In practice this type of frequency synthesizer cannot operate over a very wide range of frequencies, because the comparator will have a limited bandwidth and may suffer from aliasing problems. This would lead to false locking situations, or an inability to lock at all. In addition, it is hard to make a high frequency VCO that operates over a very wide range. This is due to several factors, but the primary restriction is the limited capacitance range of varactor diodes. However, in most systems where a synthesizer is used, we are not after a huge range, but rather a finite number over some defined range, such as a number of radio channels in a specific band.

Many radio applications require frequencies that are higher than can be directly input to the digital counter. To overcome this, the entire counter could be constructed using high-speed logic such as ECL, or more commonly, using a fast initial division stage called a prescaler which reduces the frequency to a manageable level. Since the prescaler is part of the overall division ratio, a fixed prescaler can cause problems designing a system with narrow channel spacings – typically encountered in radio applications. This can be overcome using a dual-modulus prescaler.

Further practical aspects concern the amount of time the system can switch from channel to channel, time to lock when first switched on, and how much noise there is in the output. All of these are a function of the loop filter of the system, which is a low-pass filter placed between the output of the frequency comparator and the input of the VCO. Usually the output of a frequency comparator is in the form of short error pulses, but the input of the VCO must be a smooth noise-free DC voltage. (Any noise on this signal naturally causes frequency modulation of the VCO.) Heavy filtering will make the VCO slow to respond to changes, causing drift and slow response time, but light filtering will produce noise and other problems with harmonics. Thus the design of the filter is critical to the performance of the system and in fact the main area that a designer will concentrate on when building a synthesizer system.

Use as a frequency modulator

Many PLL frequency synthesizers can also generate frequency modulation (FM). The modulating signal is added to the output of the loop filter, directly varying the frequency of the VCO and the synthesizer output. The modulation will also appear at the phase comparator output, reduced in amplitude by any frequency division. Any spectral components in the modulating signal too low to be blocked by the loop filter end up back at the VCO input with opposite polarity to the modulating signal, thus canceling them out. (The loop effectively sees these components as VCO noise to be tracked out.) Modulation components above the loop filter cutoff frequency cannot return to the VCO input so they remain in the VCO output.

This scheme therefore cannot directly handle low frequency (or DC) modulating signals but this is not a problem in the many AC-coupled video and audio FM transmitters that use this method. Such signals may also be placed on a subcarrier above the cutoff frequency of the PLL loop filter.

See also

• Superheterodyne receiver
• Digitally controlled oscillator
• Dual-modulus prescaler
• Wadley Loop

References

• Banerjee, Dean (2006), PLL Performance, Simulation and Design Handbook (4th ed.), National Semiconductor. Also PDF version.
• Crawford, James A. (1994), Frequency Synthesizer Design Handbook, Artech House, ISBN 0-89006-440-7
• Egan, William F. (2000), Frequency Synthesis by Phase-lock (2nd ed.), John Wiley & Sons, ISBN 0-471-32104-4
• Gardner, Floyd M. (1966), Phaselock Techniques, John Wiley and Sons
• Kroupa, Venceslav F. (1999), Direct Digital Frequency Synthesizers, IEEE Press, ISBN 0-7803-3438-8
• Kroupa, Venceslav F. (1973), Frequency Synthesis: Theory, Design & Applications, Griffin, ISBN 0-470-50855-8
• Manassewitsch, Vadim (1987), Frequency Synthesizers: Theory and Design (3rd ed.), John Wiley & Sons, ISBN 0-471-01116-9
• Popiel-Gorski, Jerzy (1975), Frequency Synthesis: Techniques and Applications, IEEE Press, ISBN 0-87942-039-1

Further reading

• Ulrich L. Rohde "Digital PLL Frequency Synthesizers – Theory and Design ", Prentice-Hall, Inc., Englewood Cliffs, NJ, January 1983
• Ulrich L. Rohde " Microwave and Wireless Synthesizers: Theory and Design ", John Wiley & Sons, August 1997, ISBN 0-471-52019-5

External links

• Hewlett-Packard 5100A (tunable, 0.01 Hz-resolution Direct Frequency Synthesizer introduced in 1964; to HP, direct synthesis meant PLL not used, while indirect meant a PLL was used)
• Hewlett-Packard (December 1965). Model 5100A Synthesizer (PDF). Operating and Service Manual.
• Hewlett-Packard (August 1965). Model 5110A Synthesizer Driver (PDF). Operating and Service Manual.
• Frequency Synthesizer U.S. Patent 3,555,446, Braymer, N. B., (1971, January 12)
• Oliver, Bernard M. (May 1964). "Digital Frequency Synthesis" (PDF). Hewlett-Packard Journal. 15 (9): 1.
• Van Duzer, Victor E. (May 1964). "A 0-50 Mc Frequency Synthesizer with Excellent Stability, Fast Switching, and Fine Resolution" (PDF). Hewlett-Packard Journal. 15 (9): 1–6.. HP 5100A Direct synthesizer: comb generator; filter, mix, divide. Given 3.0bcd MHz, mix with 24 MHz and filter to get 27.0bcd MHz, mix with 3.a MHz and filter to get 30.abcd MHz; divide by 10 and filter to get 3.0abcd MHz; feed to next stage to get another digit or mix up to 360.abcd MHz and start mixing and filtering with other frequencies in 1 MHz (30–39 MHz) and 10 MHz (350–390 MHz) steps. Spurious signals are -90 dB (p. 2).
• Van Duzer, Victor E. (May 1964). "Notes on the Application of Frequency Synthesizers" (PDF). Hewlett-Packard Journal. 15 (9): 7–8.
• Cutler, Leonard S. (December 1963). "Examination of the Atomic Spectral Lines of a Cesium Beam Tube with the HP Frequency Synthesizer" (PDF). Hewlett-Packard Journal. 15 (4).
• Shanahan, John. C. (December 1971). "Uniting Signal Generation and Signal Synthesis: A simultaneous solution is devised to the problems of signal generation and signal use. while optimizing both for bench and automatic use" (PDF). Hewlett-Packard Journal. 23 (4): 2–13.. HP 8660A/B Multiloop PLL synthesizer.